62 Comments

  1. jjacstcy Says Reply

    [..YouTube..] What collet have you got that bit installed to?

  2. piniw5 Says Reply

    [..YouTube..] Amazing, amazing amazing…..I really like to? see your creations.

  3. radioshack7 Says Reply

    [..YouTube..] Fantastic? work.

  4. Marcelmx3 Says Reply

    [..YouTube..] @jjacstcy Its a 1/8th inch collet, or 3,175mm in metric…One of the most used collets i have..

  5. Marcelmx3 Says Reply

    [..YouTube..] @piniw5 and @radioshack7 Thanks !! Nice to hear…..

  6. RegEditzZz Says Reply

    [..YouTube..] Hey man, nog steeds lekker bezig zie ik !Filmpjes zien er steeds beter uit en je werk was al top !Greetz

  7. ibainesy Says Reply

    [..YouTube..] a 1/8th single flute cutter??? strange why that sort of cutter? is it a cutter with plastic or aluminium specific geometry? And what sort of tool life do you get out of the engraving bit? And have you considered High Speed Steel bits, I believe they are meant to be sharper than carbide, (or maybe thats just coated carbides)

  8. Marcelmx3 Says Reply

    [..YouTube..] @RegEditzZz Uiteraard 🙂 CNC werk is verslavend hoor…

  9. Marcelmx3 Says Reply

    [..YouTube..] @ibainesy Well why this cutter? because i bought a whole bunch of them… :)I found singel flute to have the best results, and indeed a bigger spiral to shoot out the chips fast…But its full carbide? cutter, so no sticky coating. Same apply’s to VHM, use blank ones, not coated with like Tialnbut if you have 2 cutters, and one of them is sharper… go for it..And remember, what i say is not based on whats really best, its just my experience, and i try to learn from all your input to..

  10. GEK69NY Says Reply

    [..YouTube..] Hi. That is great job! Let me ask you who writes all those commands for CNC machine or it just programs itself after a picture analyzing? Thanks in advance!

  11. Marcelmx3 Says Reply

    [..YouTube..] @GEK69NY Designs can be convertede to cnc code (named : G-code) by CAM software.But there are a lot of good programs that combine design, simulate, and code.Take a look at Artcam, or vectric v-carve, vertric aspire etc.?

  12. GEK69NY Says Reply

    [..YouTube..] Other wards you don’t have to be an engineer to do all that nice job, am I right? Thanks!

  13. Marcelmx3 Says Reply

    [..YouTube..] @GEK69NY That’s right….. Although i do think that its best to? understand G-code…If something strange happens you can find out whats the problem…But indeed Learning to work with Photoshop is much more difficult then engraving a led sign… 🙂

  14. fretsman68 Says Reply

    [..YouTube..] Very well done, may I ask where you get the extruded light bases?Thanks,Dave

  15. eFalegname Says Reply

    [..YouTube..] Chambonea, dale chambonea.? Great!

  16. Marcelmx3 Says Reply

    [..YouTube..] @eFalegname Google can not help me translate this one…. 🙂 But thanks anyway 😉

  17. qiubolesque Says Reply

    [..YouTube..] Felicidades por tu trabajo, que perfil usas para colocarle los leds?

  18. RoboCNCnl Says Reply

    [..YouTube..] @qiubolesque Perfil Led en China.No tengo ninguna relación directa más desafortunado.

  19. jjacstcy Says Reply

    [..YouTube..] What lighting kits/fixtures are you using?

  20. jjacstcy Says Reply

    What lighting kits/fixtures are you using?

  21. RoboCNC Frees- & Graveerwerk Says Reply

    @jjacstcy The aluminum comes from redsun China

  22. RoboCNC Frees- & Graveerwerk Says Reply

    @jjacstcy The aluminum comes from redsun China

  23. RoboCNC Frees- & Graveerwerk Says Reply

    @jjacstcy The aluminum comes from redsun China

  24. Tubeknijper Says Reply

    [..YouTube..] Weer wat geleerd

  25. Tubeknijper Says Reply

    Weer wat geleerd

  26. RoboCNCnl Says Reply

    [..YouTube..] @Tubeknijper? Daar doen we het voor 😉 Zo als ergens op cnczone als onderschrift word gebruikt, ‘ kennis vermenigvuldigd zich als je het deelt’

  27. RoboCNCnl Says Reply

    [..YouTube..] Daar doen we het voor 😉 Zo als ergens op cnczone als onderschrift word gebruikt, ‘ kennis vermenigvuldigd zich als je het deelt’

  28. RoboCNC Frees- & Graveerwerk Says Reply

    @Tubeknijper Daar doen we het voor 😉 Zo als ergens op cnczone als onderschrift word gebruikt, ‘ kennis vermenigvuldigd zich als je het deelt’

  29. RoboCNC Frees- & Graveerwerk Says Reply

    @Tubeknijper Daar doen we het voor 😉 Zo als ergens op cnczone als onderschrift word gebruikt, ‘ kennis vermenigvuldigd zich als je het deelt’

  30. RoboCNC Frees- & Graveerwerk Says Reply

    @Tubeknijper Daar doen we het voor 😉 Zo als ergens op cnczone als onderschrift word gebruikt, ‘ kennis vermenigvuldigd zich als je het deelt’

  31. firefoxik75 Says Reply

    [..YouTube..] What is that stand with LEDs ? Still looking for something like that, its really cool…

  32. firefoxik75 Says Reply

    What is that stand with LEDs ? Still looking for something like that, its really cool…

  33. RoboCNC Frees- & Graveerwerk Says Reply

    @firefoxik75 Did you read all on the ‘Full info link” ? The profiles are from redsun china. dont know if you could buy a small part, i did a 500$ shipment… Never seen them anywhere else, or i do not know the right search keywords… Good luck..

  34. RoboCNC Frees- & Graveerwerk Says Reply

    @firefoxik75 Did you read all on the ‘Full info link” ? The profiles are from redsun china. dont know if you could buy a small part, i did a 500$ shipment… Never seen them anywhere else, or i do not know the right search keywords… Good luck..

  35. RoboCNC Frees- & Graveerwerk Says Reply

    @firefoxik75 Did you read all on the ‘Full info link” ? The profiles are from redsun china. dont know if you could buy a small part, i did a 500$ shipment… Never seen them anywhere else, or i do not know the right search keywords… Good luck..

  36. Wolffie Says Reply

    lOVE, LOVE, LOVE THIS.
    Can’t wait to learn how to do it and get started.
    Cheers
    Wolffie

  37. Famous Artist Music Says Reply

    you can eliminate a lot of issues if you use RASTER

  38. RoboCNC Frees- & Graveerwerk Says Reply

    Hi there… Thank you for your input… If you look closely to the video i use both raster, and contour toolpaths.. In my ‘opinion’ both suit a different purpose… and are chosen accordingly. But i use raster most of the times indeed,

  39. RoboCNC Frees- & Graveerwerk Says Reply

    Hi there… Thank you for your input… If you look closely to the video i use both raster, and contour toolpaths.. In my ‘opinion’ both suit a different purpose… and are chosen accordingly. But i use raster most of the times indeed,

  40. RoboCNC Frees- & Graveerwerk Says Reply

    Hi there… Thank you for your input… If you look closely to the video i use both raster, and contour toolpaths.. In my ‘opinion’ both suit a different purpose… and are chosen accordingly. But i use raster most of the times indeed,

  41. maurizio sili Says Reply

    BONJOUR GE SUIS CNC SMG Can you tell me where you buy suport for years aluminiome plexiglass you ave with serious or led me provide you Can y addressed here is my imail (maurizio_42@hotmail.com) cordially you made ??the hats be working fine

  42. RoboCNC Frees- & Graveerwerk Says Reply

    These profiles can be purchased with us (RoboCNC dot nl). I will contact you on your email address.

  43. RoboCNC Frees- & Graveerwerk Says Reply

    These profiles can be purchased with us (RoboCNC dot nl). I will contact you on your email address.

  44. RoboCNC Frees- & Graveerwerk Says Reply

    These profiles can be purchased with us (RoboCNC dot nl). I will contact you on your email address.

  45. paulo cohelo Says Reply
  46. Steve Says Reply

    Do you know what the profile number or part number is for the light stands you used? Thank you.

    • Robo Says Reply

      Dear Steve,

      Please contact me through the email form for extra information.
      The profiles can be purchased directly with us.

  47. Larry J. Maddox Says Reply

    I have a Honda 450 Rebel for trade for a CNC machine if anyone willing. ljmaddox@gmail.com

  48. Lennie Metz Says Reply

    How well does this work in outdoors? I live in a tropical climate with a lot of pollution that affects plastic. could I put glass over the acrylic to protect from the elements?

  49. RoboCNC Frees- & Graveerwerk Says Reply

    Hi Lennie, Yes for outdoors you could use a different profile (Check my other video’s on acrylic ). Glass would not effect the engraving or the light, so i think this would be fine.

  50. RoboCNC Frees- & Graveerwerk Says Reply

    Hi Lennie, Yes for outdoors you could use a different profile (Check my other video’s on acrylic ). Glass would not effect the engraving or the light, so i think this would be fine.

  51. RoboCNC Frees- & Graveerwerk Says Reply

    Hi Lennie, Yes for outdoors you could use a different profile (Check my other video’s on acrylic ). Glass would not effect the engraving or the light, so i think this would be fine.

  52. yudomax Says Reply

    Hi, I’m trying to make large acrylic panels with leds on its edged and engrave on top of it with a drill bit (I have no lasser CNC Router for example)… I’ve tried many different ways and wasted already some big money but can’t make a good illumination. Is there something I’m missing while engraving? I’ve tried with panel printing (white ink) but I haven’t been successful… PLEASE HELP ME!!! the acrylic plates are 7.8×3.9 ft and 0.65 inches thick…

  53. CNC Flake Says Reply

    Wonderful!

  54. Snr Carver Says Reply

    Photoshop is very time consuming to learn and I don’t think I have the patience to learn this and also PhotoVCarve – (‘n beetje boven my pet) I am fully au fait with Corel Draw – can this be some form of substitute? (sorry my Dutch has faded over the years outside the country.)

    Ik ben 78 jaar en heb niet meer zo veel kracht over maar ik wil nog steeds graag meedoen aan deze
    hobby – zit in ‘n rystoel maar kom goed by de masjiene – als ik iets gemaakt hebt zal ik het laten zien..

    My main aim is to use a normal jpeg or bmp photo file and try and make these into nice relief carvings –
    I like doing birds and animals.

    Thank you for all the hints and tuition – this is a terrific site, I’m glad i found it.

    • Robo Says Reply

      Hi Snr Carver and thanks for your nice comment !
      To make it easy I will answer in English, but I do love the effort you did in speaking dutch again, thumbs up.

      Photoshop, PhotoVcarve and coreldraw can not be compared to each other i’m afraid.
      Photoshop is to retouch or color-correct and resize images for example. (For your projects not really needed).
      Coreldraw can be very handy in CNC world, as the output can be set to vectors and can be used to engrave or design CNC work.
      But you mention to want to carve jpegs and bitmaps, I think their is only one easy solution, and that is PhotoVcarve from Vectric.com.
      I have made a tutorial video, I do think you should have a look at this page : https://www.robocnc.nl/?p=2121

      Good luck, and don’t give up if the first try wont work out…
      Beste regard, / Met vriendelijke groet,
      Marcel

  55. Kees Moret Says Reply

    Hoi Robo.Hoe bevestig jij je werkstuk op tafel?Het ziet er uit als dubbelzijdige tape.Groeten, Kees.

  56. Win Brayer Says Reply

    Can you tell us how you made the vacumn accessory for your CNC machine?

    • Robo Says Reply

      There is no vacuum accessory to be seen on this page, nor in the video.
      I do not understand what you mean.

      Please search our website, probably the information you request is already on the website.

  57. Ondino rojas Says Reply

    buenas noches por favor si le es posible indicar que programa usa para elaborar los diseños gracias

  58. Minh Chau Says Reply

    thâ?t la? công nghê? siêu ???ng

Leave a Reply